How to Replace the Replacement Key Battery For the Saab 9-3
Saab owners have a unique procedure to add the second key. It requires dealer service with a handheld computer dubbed Tech-2. Then the transponder must be replaced and a key must be purchased.
It is a good idea to rotate your keys in order that one does not get worn out more quickly than the other. This will also ensure that your keys remain in top shape.
Replacement Case
The new key fobs are not like the older Saab keys. They're equipped with electronic devices that make it difficult to copy. This has made car theft much more difficult than it was twenty years ago. It has also made it more expensive to replace keys lost.
Every owner of a Saab 9-3 must have at least two functioning keys. If one of them is lost, it costs a lot of money to add another to the car since it requires replacing the CIM module and re-programming the locking cylinders. Dealers usually charge between $100 and $200 for this.
There are ways to reduce these high costs. Some parts dealers can look up the code on an old key (usually the same one that opens the doors and turns on the ignition) and cut a new metal key blade for a fraction of the dealer's cost. The key must be exactly the same as the original in order for it to work in your vehicle.
You can also replace the case yourself by following these steps. You will need to have an open-faced screwdriver and patience. With the screwdriver, pry apart the plastic and remove the emergency key. Once the case is open, remove all electronics and put them back in the new case. Make sure you insert the correct key and badge inside the case.
Replacement Battery
The Saab 9-3 replacement battery is a budget component that can be easily and quickly replaced. This DIY video from YouTube Cyclone Cyd shows how to replace the remote key fob battery in only four steps. This tutorial is compatible with any modern Saab key fob. However, the procedure may differ slightly.
The button is normally located just below the Saab logo on the back of the fob. This button is typically located on the back of your fob, next to the Saab Logo. Next take the flathead screwdriver to insert into the small hole of this button. This will be enough to allow you to open the fob's case to allow you to replace the battery.
Once the new CR1632 battery is installed it is possible to reassemble the remote key fob and program it to your car. The whole process should not take more than an hour. This is a straightforward process that doesn't require any special tools.
If you lose a key, the process is more complicated but it is still able to be completed. The dealer will have to find the VIN number of the car and then order a replacement key blade and TWICE module, both with the correct unique code. The dealer will then have to program the key using MDI, a new software tool.
Replacement Key Fob
The key fob is the device that locks and unlocks your car, it's got a battery inside. Batteries have a finite lifespan and will eventually die. This is a typical issue that happens to all cars and the good news is that you can change the batteries in most key fobs without replacing the whole case. Amazon sells replacement fobs that have all the electronic components installed. It is easy to open the case and replace the batteries. It is necessary to remove the emergency key before you can replace the batteries. To do this, you need to insert the screwdriver of a small flat head into the slot that is in the middle. Work the screwdriver around the case until it will split open, making it simple to take it out.
When you're ready to replace your keys, ensure that you have spare keys, as this can reduce the total cost by a significant amount. If you have a spare, you can have the dealer cut a new key and program it to the car, which is cheaper than replacing the entire key fob.
It is possible to add another key to your car If you don't already have one, but it takes an extensive amount of research and work. It will cost you a few hundred dollars to get a second car key. saab key programming near me in the car must also be programmed. This can be accomplished by a professional, but it's an expensive option for the majority of owners.
Replacement Ignition
Unlike earlier Saab vehicles, the latest SAAB 9-3 models are equipped with a much more sophisticated alarm system that is built around a coded key. This means that should you lose only one functioning key, getting another one could be very expensive because the car needs to have a computer module installed, and it must also be programmed to accept an additional key. Dealers can even charge hundreds of dollars to program a new key in the event that they are unable to do it.
If you've lost the only working key the dealer will replace your car's computer (known as the CIM or SAAB TWICE) to create an exchange, and they will charge a premium for it. Instead we can reprogramme the EEPROM in your current car computer to allow it to be programmed for a replacement key, saving you over 50% of what you'd have to pay at a dealership.
If you have owned a 9-3 from SAAB for many years and you're aware of the ignition keys aren't very durable. If your ignition key is not working properly, you should look into replacing it. They can become very sticky and the buttons have been known to fall off. It's not as difficult as it seems to replace the ignition key. With the proper tools, it can be accomplished in a matter of minutes.